KEB F5 MANUAL PDF

Before working with the unit the user must become familiar with it. This especially applies to the knowledge and observance of. Hide thumbs. The desired function is adjusted with Pn and.

Author:Tojataxe Moogugul
Country:Angola
Language:English (Spanish)
Genre:Travel
Published (Last):1 May 2008
Pages:323
PDF File Size:13.83 Mb
ePub File Size:8.69 Mb
ISBN:391-2-66533-571-9
Downloads:9749
Price:Free* [*Free Regsitration Required]
Uploader:Gogal



KEB f5. Lisez d'abord le manuel d'instructions partie 1! Read Instruction manual part 1 first! Prima leggere il manuale di controllo parte 1! Leer manual de instrucciones parte 1! Vor jeglichen Arbeiten mu? Darunter f? It is only valid together with the Instruction Manuals Part 1 and Part 2.

Both Instruction Manuals must be made available to the user. Prior to performing any work on the unit the user must familiarize himself with the unit. This includes especially the knowledge and observance of the safety and warning directions of Part 1. Este manual de instrucciones debe ser accesible a todos los usuarios. Antes de conectar el convertidor, el usuario debe de familiarizarse con el convertidor, especialmentedebe de tene en cuenta las medias de seguridad y advertencias.

RU - 38? KEB Error Diagnosis Installation and Connection 1. Lay shield on one side of the inverter onto earth potential? Lay control and power cable separately about Lay crossings in a right angle in case it cannot be prevented EMC 1.

External analog set-point setting see CP. The internal resistance is reduced to 30 k?. To prevent undefined conditions at external power supply the basic procedure is to first switch on the power supply and after that the inverter. X2A 24 25 26 27 28 29 PE max. Do no exceed the maximum output current of mA. RLC changed with CP. FLC 1. Operation of the Unit As an accessory to the local or external option: cable When starting the inverter whitout an operator, it is started with the last stored values or factory setting.

Digital Operator Standard: Part No. Principally during a change, parameter values are immediately accepted and stored non-volatile. However, with some parameters it is not useful that the adjusted value is accepted immediately. In these cases CP. If a malfunction occurs during operation, then the actual display is overwritten by the alarm message. In the inverter status display CP. In order to reset the error itself, the cause must be removed or a power-on reset must be made.

After parameterizing the unit can be barred against unauthorized access Passwords: see last but one page. The adjusted mode is stored. Actual frequency display Display of the actual output frequency with a resolution of 0. The operator displays additionally? The rotation of the inverter is indicated by the sign. Output frequency The indication is done in the same manner as at CP.

For control reasons the set frequency is displayed even if control release or direction of rotation are not switched. If no direction of rotation is set, the set frequency for clockwise rotation forward is displayed.

Inverter status display The status display shows the actual working conditions of the inverter. Other status messages are described at the parameters, where they GB occur. Apparent current Display of the actual apparent current in ampere.

For that the highest value of CP. The switch off of the inverter also clears the memory. Utilization Display of the actual inverter rate of utilization in percent. Only positive values are displayed, meaning there is no differentiation between motor and regenerative operation. Intermediate circuit voltage Display of actual DC voltage in volt. OP Under volt. UP … V DC approx. Output voltage Display of the actual output voltage in volt.

Internal limiting of the fixed frequencies CP. Adjustment range: Resolution: Factory setting: The actual acceleration time is proportional to the frequency change. The actual deceleration time is proportional to the frequency change. This is achieved through a straightening of the acceleration and deceleration ramps.

The straightening time, also called S-curve time, can be adjusted with CP. Adjustment range: Resolution: Factory setting: 0,00 off To keep the breakdown torque nearly constant over the entire speed range, the voltage decrease can be compensated with the boost.

UA Adjustment range: Resolution: Factory setting: 0, Determine the rate of utilzation in no-load operation with rated frequency? Preset about 10 Hz and adjust the boost, so that about the same rate of utilization is reached as with the rated frequency.

When the motor, during continuous operation, drives with low speed and too high voltage it can lead to an overheating of the motor. Rated frequency With the adjusted frequency the inverter reaches a maximal output voltage. The adjustment of the rated motor frequency is typical in this case.

Note: Motors can overheat when the rated frequency is UA incorrectly adjusted! These adjustments can be ignored at the initial startup. With this parameter a regulated output voltage in relation to the rated frequency can be adjusted. The function allows, among other things, an adaption of the output voltage to special motors.

Adjustment range: Resolution: Factory setting: Note: The employed power stage determines the maximum switching frequency as well as the factory setting see manual: part2. Refer to following list to learn about influences and effects of the switching frequency.

Step frequency The fixed frequencies are selected with the inputs I1 and I2. Adjustment range: Resolution: Factory settingCP. The negative values are released in application mode. The rotation source of the fixed frequencies is not changed by CP. Quick braking is caused by D. This parameter determines how the dc-braking is triggered. Value 0 1 Activation DC-braking; deactivated DC-braking; at switch off of the direction of rotation and upon reaching 0Hz.

The braking time is CP. DC-braking; as soon as setting for the direction of rotation is absent. DC-braking; as soon as the direction of rotation changes or is absent. DC-braking; on disabling the direction of rotation and if the real frequency falls below 4 Hz. DC-braking; when the real frequency falls below 4 Hz.

GB DC-braking; as soon as the set value falls below 4 Hz. DC-braking; when input I4 is switched. Braking time depends on the real frequency. When the ramp reaches the adjusted value,it is stopped so long until the current decreases again. When exceeding the adjusted value, the output frequency is reduced until the value drops below the adjusted value. With activated speed search the inverter searches for the actual motor speed, adapts its output frequency and accelerates with the adjusted ramp to the given set value.

During speed search CP. The parameter determines, under what conditions the functions operate. In case of several conditions the sum of the value must be entered.

LA PASSIONE DI ARTEMISIA SUSAN VREELAND PDF

Keb inverter f5 manual

KEB f5. Lisez d'abord le manuel d'instructions partie 1! Read Instruction manual part 1 first! Prima leggere il manuale di controllo parte 1! Leer manual de instrucciones parte 1! Vor jeglichen Arbeiten mu? Darunter f?

DOCOPEN BM PDF

KEB F5 App Manual

This is how to quickly and effectively start-up an asynchronous induction motor using our F5 drive. Specifically, we will be highlighting a KEB F5 startup in closed-loop control with encoder feedback. The general process will be similar for other motors and control types. In general, there are five main components that will be required for a KEB F5 startup using your particular motor. They are:. We can then perform a device scan to locate the F5 drive.

2SC5200 TOSHIBA PDF

KEB F5-B AC-Drive Manual

F5-A,-E,-H 4. Table of Contents. Page 1. Table of contents. Description of the controls.

Related Articles